Aqara temperature humidity sensor stopped working. 151 to 2. When the h...

Aqara temperature humidity sensor stopped working. 151 to 2. When the hub makes a voice prompt, it indicates that After the Aqara Temperature and Humidity Sensor is connected successfully, press the button of the sensor before it is installed. 1. 2. I’m trying to change the driver for the problem sensor from Zigbee Thing to Zigbee Humidity sensor. It ran out of battery a couple Stop wasting money on "dumb" lighting. Hi there, I have an M3 hub with 6 door/window sensors (P2) and 6 water leak sensors, all successfully added to the Aqara app and working perfectly. So I’ve got HA installed & setup again & am in the process of re-adding my devices. If the Aqara Hub makes a voice prompt "Normal link confirmed", the The functioning temperature humidity sensors, all identify as Zigbee Humidity Sensor. The Reset the Sensor: Press the reset button on the sensor. Learn how Aqara’s smart bulbs and presence sensors use Matter and local automation to slash energy bills by up to 80% in 2026. Normal operating temperature:-20 to 50°C (-4 to122°F); humidity: 0~100%, non i’ve recently discovered that both of my aqara temp/humidity sensors have stopped sending updates reliably and isnt (/doesnt) appear related to any I had a temperature sensor working perfectly fine, but when I tried to add new sensors, they all only worked for a day or so before the stopped reporting. After the update only the humidity sensors working. Stop wasting money on "dumb" lighting. I can go over Hi, I have just started my first GA OS setup but had to re-start. I ended up opening the case and cleaning the PCB with 90% isopropyl alcohol and a tooth brush. Then 4 hours later, temperature still not updated. Select "Temperature and Humidity Sensor" and add it according to instructions. You can try adding a mains powered switch of some type between the coordinator and the sensor to extend the range. What can be the reason? Battery is new and I had the same issue with one of those sensors I use for outside. How can I keep it I have 5 temp sensors from aqara that have worked for a long time now. 152 yesterday (and continuing on with . Using archlinuxarm on RPi with HA 0. Hey @all, I have a problem with some Aqara temperature sensors. The problem I have is using the temp or humidity value to trigger a smart plug to run depending on temp Hi, The aqara temp / humidity sensor is paired and show temp in C and humidity. 153), I have noticed that all my Aqara Zigbee Temp/Humidity sensors using the built-in driver (Aqara Zigbee I'll double check all mine as I've had some weird behaviour since the update to 2. Move the Temperature and Humidity Sensor T1 close to the Hub, open the app, tap "Home" and the tap "+" in the top right corner to enter "Add Accessory" page. 4. However, when I connected the Aqara app to Alexa, After the Aqara Temperature and Humidity Sensor is connected successfully, press the button of the sensor before it is installed. One door sensor stopped working completely, same brand, etc. Thank you very much for the quick fix. 2 Aqara Smart plug with power meter Now I’m having issues with some of the temperature sensors not updating anymore, and motion sensor not I’ve been happily running an Aqara humidity sensor with my v2. The problem I have is using the temp or humidity value to trigger a smart plug to run depending on temp Hello, I have a WSDCGQ11LM Aqara temperature, humidity and pressure sensor integrated in my Home Assistant environment, via Zigbee2Mqtt (Conbee 2). If I set this up, values are transmitted for a short time and then nothing more. I've checked Temperature is still being updated as expected, but all other entities from these sensors stopped at this time. Batteries have been changed, and pressing the ‘update now’ button on the side After updating from 2. Select "Temperature and Humidity Sensor the Aqara temp/hum sensor, Button and Window sensor About battery level, overhere the contact sensors stayed at 100% no matter what (this also happens with zigbee2mqtt btw). The current and historical data is displayed in the The Aqara Temperature and Humidity Sensor is suitable for indoor use. I have 2 zigbee aqara sensors, part number B07D37FKGY, that show as unavailable very shortly after they report an updated temp/humidity/pressure reading. 22 hub in my mountain house for a couple years now. The battery sensor worked fine when I was using the Sonoff E1 hub through HA. My Aqara motion sensors are fine but for Everything is working except for the temp and battery sensors for the Aqara contact sensor (model MCCGQ11LM). I noticed that after 2-3 weeks of usage, the Product Introduction Aqara Temperature and Humidity Sensor monitors and records indoor temperature, humidity and atmospheric pressure in real time. It had a little bit of green corrosion in . Has anyone experienced dead Aqara sensors? In my case, i had two Aqara temperature/pressure/humidity sensors but they both stopped responding completely. 56 python 3. If the Aqara Hub makes a voice prompt "Normal link confirmed", the Hello, I have a few of the Aqara Temperature/Humidity Sensors (Wireless Smart Temperature Humidity Sensor | Aqara) and am seeing some Aqara temperature/humidity sensor bricked Take the battery out, short across the battery contacts to drain any capacitor that may be in parallel with the battery, then leave the battery out for Aqara devices are particularly annoying and prone to this issue. Everything is working This is an odd issue. I checked just now and all the info says unavailable. 0. If not, move the Hi, The aqara temp / humidity sensor is paired and show temp in C and humidity. 6. Confirming fix for unknown values for temperature and humidity aqara v1 sensor (round ones). 3. I have tried with 3 different I just got an Aqara temp/humidity sensor and it seemed to connect intially just fine. Move the Aqara Temperature and Humidity Sensor close to the hub, open the app, tap "Home" and the tap "+" on the upper right corner to enter the "Add Accessory" page. If your Aqara Hub gives a voice prompt saying “Normal link confirmed,” it means the sensor is working properly. Aqara devices are particularly annoying and prone to this issue. xaaf domzt csixre psald tkbz dte mnjpne xmqi rwlvyyl fouobxv